Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSACURA1997INTEGRA GS-R, 2D COUPEREPAIR AND DIAGNOSIS (SINGLE PAGE)GENERAL INFORMATIONDTC INDEXENGINE PERFORMANCE DTCS (GS-R)
1997 Acura Integra GS-R, 2D Coupe
Engine Performance DTCS (GS-R)
1997 Acura Integra GS-R, 2D CoupeSECTION Engine Performance DTCS (GS-R)
ENGINE PERFORMANCE DTCS (GS-R)
| DTC | OEM Code | Description |
|---|---|---|
| P0106 | 5 | Manifold Absolute Pressure (MAP) Sensor Range/Performance |
| P0107 | 3 | MAP Sensor Low Input Voltage |
| P0108 | 3 | MAP Sensor High Input Voltage |
| P0111 | 10 | Intake Air Temperature (IAT) Sensor Range/Performance |
| P0112 | 10 | IAT Sensor Low Input Voltage |
| P0113 | 10 | IAT Sensor High Input Voltage |
| P0116 | 86 | Engine Coolant Temperature (ECT) Sensor Range/Performance |
| P0117 | 6 | ECT Sensor Low Input Voltage |
| P0118 | 6 | ECT Sensor High Input Voltage |
| P0122 | 7 | Throttle Position (TP) Sensor Low Input Voltage |
| P0123 | 7 | TP Sensor High Input Voltage |
| P0131 | 1 | Primary HO2S-1 Circuit Low Voltage |
| P0132 | 1 | Primary HO2S-1 Circuit High Voltage |
| P0133 | 61 | Primary HO2S-1 Slow Response |
| P0135 | 41 | Primary HO2S-1 Heater Circuit Malfunction |
| P0137 | 63 | Secondary HO2S-2 Circuit Low Voltage |
| P0138 | 63 | Secondary HO2S-2 Circuit High Voltage |
| P0139 | 63 | Secondary HO2S-2 Slow Response |
| P0141 | 65 | Secondary HO2S-2 Heater Circuit Malfunction |
| P0171 | 45 | System Too Lean |
| P0172 | 45 | System Too Rich |
| P0301 | 71 | Misfire Cylinder No. 1 Detected |
| P0302 | 72 | Misfire Cylinder No. 2 Detected |
| P0303 | 73 | Misfire Cylinder No. 3 Detected |
| P0304 | 74 | Misfire Cylinder No. 4 Detected |
| P0325 | 23 | Knock Sensor (KS) Circuit Malfunction |
| P0335 | 4 | Crankshaft Position (CKP) Sensor Circuit Malfunction |
| P0336 | 4 | CKP Sensor Range/Performance |
| P0420 | 67 | Catalyst System Efficiency Below Threshold |
| P0441 | 92 | EVAP Emission System Inadequate Purge Flow |
| P0500 | 17 | Vehicle Speed Sensor (VSS) Circuit Malfunction |
| P0505 | 14 | Idle Control System Malfunction |
| P1106 | 13 | Barometric Pressure (BARO) Circuit Range/Performance |
| P1107 | 13 | BARO Circuit Low Input Voltage |
| P1108 | 13 | BARO Circuit High Input Voltage |
| P1121 | 7 | Throttle Position (TP) Lower Than Excepted |
| P1122 | 7 | TP Higher Than Excepted |
| P1128 | 5 | Manifold Absolute Pressure (MAP) Lower Than Excepted |
| P1129 | 5 | MAP Higher Than Excepted |
| P1259 | 22 | VTEC System Malfunction |
| P1297 | 20 | Electrical Load Detector (ELD) Low Input Voltage |
| P1298 | 20 | ELD High Input Voltage |
| P1300 | 71, 72, 73, Or 74 | Random Misfire |
| P1301 | 71 | Random Misfire |
| P1302 | 72 | Random Misfire |
| P1303 | 73 | Random Misfire |
| P1304 | 74 | Random Misfire |
| P1336 | 54 | Crankshaft Speed Fluctuation (CKF) Sensor Intermittent Interruption |
| P1337 | 54 | CKF Sensor No Signal |
| P1359 | 8 | Crankshaft Position/Top Dead Center/Cylinder Position (CKP/TDC/CYP) Sensor Disconnected |
| P1361 | 8 | TDC Sensor Intermittent Interruption |
| P1362 | 8 | TDC Sensor No Signal |
| P1381 | 9 | CYP Sensor Intermittent Interruption |
| P1382 | 9 | CYP Sensor No Signal |
| P1508 | 14 | Idle Air Control (IAC) Valve Circuit Failure |
| P1607 | - | PCM Internal Failure |
| P1660 | 70 | A/T FI Data Line Failure |
| P1681 | 30 | A/T FI Signal "A" Low Input |
| P1682 | 30 | A/T FI Signal "A" High Input |
| P1686 | 31 | A/T FI Signal "B" Low Input |
| P1687 | 31 | A/T FI Signal "B" High Input |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.