Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1997 Acura 2.2CL StandardFACTORY OEM SERVICE PROCEDURE
Engine Controls - Tests W/Codes
- Introduction
- Self-Diagnostic System
- Test Equipment
- Summary
- Connector Identification
- Circuit Tests
- Notes
- Malfunction Indicator Light (Mil)
- DTC P0106: Manifold Absolute Pressure (Map) Sensor System Vacuum Leak
- DTC P0107: Manifold Absolute Pressure (Map) Sensor Low Input Voltage
- DTC P0108: Manifold Absolute Pressure (Map) Sensor High Input Voltage
- DTC P0112: Intake Air Temperature (IAT) Sensor Low Input Voltage
- DTC P0113: Intake Air Temperature (IAT) Sensor High Input Voltage
- DTC P0116: Engine Coolant Temperature (ECT) Sensor Range/Performance Problem
- DTC P0117: Engine Coolant Temperature (ECT) Sensor Low Input Voltage
- DTC P0118: Engine Coolant Temperature (ECT) Sensor High Input Voltage
- DTC P0122: Throttle Position (TP) Sensor Low Input Voltage
- DTC P0123: Throttle Position (TP) Sensor High Input Voltage
- DTC P0131: Primary Heated Oxygen Sensor (Ho2S-1) Low Voltage
- DTC P0132: Primary Heated Oxygen Sensor (Ho2S-1) High Voltage
- DTC P0133: Primary Heated Oxygen Sensor (Ho2S-1) Slow Response
- DTC P0135 & P0141: Heated Oxygen Sensor (Ho2S) Heater Circuit Malfunction
- DTC P0137: Rear Heated Oxygen Sensor (Ho2S-2) Low Output Voltage
- DTC P0138: Rear Heated Oxygen Sensor (Ho2S-2) High Output Voltage
- DTC P0139: Rear Heated Oxygen Sensor (Ho2S-2) Slow Response
- DTC P0171 & P0172: Fuel System Too Lean Or Too Rich
- DTC P0301, P0302, P0303 & P0304: Misfire In One Cylinder
- DTC P0335, P0336, P1361 & P1362: Crankshaft Position/Top Dead Center (CKP/TDC) Sensor
- DTC P0401: EGR System Insufficient Flow Detected
- DTC P0420: Catalyst System Efficiency Below Threshold
- DTC P0441: Evaporative Emission (EVAP) Control Insufficient Purge Flow
- DTC P0500 & P0501: Vehicle Speed Sensor (VSS) Circuit Malfunction
- DTC P0505: Idle Control System Malfunction
- DTC P1107 & P1108: Barometric Pressure (BARO) Sensor Circuit High/Low Input Voltage
- DTC P1253: VTEC Solenoid Valve Circuit Malfunction
- DTC P1297: Electrical Load Detector (Eld) Low Voltage Input
- DTC P1298: Electrical Load Detector (Eld) High Voltage Input
- DTC P1300 Or P0301, P0302, P0303 & P0304: Random Misfire
- DTC P1359: Crankshaft Position/Top Dead Center (CKP/TDC) Sensor Disconnected
- DTC P1381 & P1382: Cylinder Position (CYP) Sensor
- DTC P1459: EVAP Purge Flow Switch Malfunction
- DTC P1491: EGR Valve Lift Insufficient Detected
- DTC P1498: EGR Valve Lift Sensor High Voltage
- DTC P1508: Idle Air Control (IAC) Valve Circuit Failure
- DTC P1607: Powertrain Control Module (Pcm) Internal Circuit Failure
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.