Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1995 Acura Legend GS, AutomaticFACTORY OEM SERVICE PROCEDURE
Code 12 - EGR System
- Turn ignition off. Remove ACG (No. 15, 7.5-amp) from fuse in underdash fuse box for 10 seconds to reset ECM. Warm engine until cooling fan comes on. Road-test vehicle about 10 minutes, keeping engine speed about 1700-2500 RPM. Retrieve codes. If Code 12 does not appear, problem is intermittent. Inspect for poor connections at ECM, EGR valve, control box, and shock tower wiring harness connectors.
- Test-drive vehicle and retest. If Code 12 appears, start engine. Disconnect No. 11 hose from EGR valve. See Fig 1 . Start engine. Check for vacuum at hose. If there is no vacuum, go to step 4). If vacuum exists, unplug 4-pin connector from control box, located on right side of engine bulkhead. Test for vacuum again on No. 11 hose. If vacuum exists, check vacuum hose routing. If routing is okay, replace EGR control solenoid valve.
- If there is no vacuum, turn ignition off. Unplug connector "A" from ECM. Test for continuity between White wire terminal of 4-pin connector and ground. If continuity exists, repair short in White wire between EGR control solenoid valve and ECM connector terminal A11. If continuity does not exist, temporarily substitute known good ECM, then retest system.
- If there was no vacuum during first vacuum test in step 2), connect vacuum pump to EGR valve. With engine idling, apply 8 in. Hg to EGR valve. If engine does not stall or run rough, or EGR valve does not hold vacuum, replace EGR valve.
- If engine stalls or runs rough, and EGR valve holds vacuum, unplug 4-pin connector from control box. Measure voltage between Black/Yellow wire terminal and body ground. If battery voltage does not exist, repair open in Black/Yellow wire between solenoid valve and FUEL PUMP fuse (No. 22, 20-amp) in underdash fuse box.
- If battery voltage exists, install "T" fitting into No. 11 hose. Connect vacuum gauge to "T" fitting. Start engine, and allow it to idle. Connect battery voltage to terminal "A" of control box connector. See Fig 2 . While observing vacuum gauge, connect terminal "B" to negative battery terminal.
- If gauge indicates 6 in. Hg within one second, go to step 9). If gauge does not indicate 6 in. Hg within one second, turn ignition off. Inspect hoses for leaks, restrictions, or misrouting. Repair as necessary. If hoses are okay, disconnect lower hose from EGR control solenoid valve.
- Connect vacuum gauge to hose. See Fig 3 . Start engine, and allow it to idle. If vacuum is not 4.8-6.8 in. Hg, replace Constant Vacuum Control (CVC) valve. If vacuum is 4.8-6.8 in. Hg, replace EGR control solenoid valve.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
