Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSACURA1995INTEGRA (GS-R) L4-1797CC 1.8L DOHC (VTEC)REPAIR AND DIAGNOSISPOWERTRAIN MANAGEMENTIGNITION SYSTEMRELAYS AND MODULES - IGNITION SYSTEMIGNITION CONTROL MODULETESTING AND INSPECTION
1995 Acura Integra (GS-R) L4-1797cc 1.8L DOHC (VTEC)
Ignition Control Module: Testing and Inspection
1995 Acura Integra (GS-R) L4-1797cc 1.8L DOHC (VTEC)SECTION Testing and Inspection
NOTE: If the Malfunction Indicator Lamp (MIL) blinks, see appropriate Diagnostic Trouble Code chart in Computers and Control Systems before testing the coil.
- Perform an input test for the Ignition Control Module (ICM) after finishing the fundamental tests for the ignition system and the fuel and emissions systems.
- The tachometer should operate normally.
1. Remove the distributor cap, the distributor rotor, and the leak cover.
2. Disconnect the BLK/YEL, WHT/BLU, YEL/GRN, and BLU wires from the ICM.
3. Turn the ignition switch ON. Check for voltage between the BLK/YEL wire and body ground. There should be battery voltage.
- If there is no battery voltage, check the BLK/YEL wire between the ignition switch and the ICM.
- If there is battery voltage, go to step 4.
4. Turn the ignition switch ON. Check for voltage between the WHT/BLU wire and body ground. There should be battery voltage.
- If there is no battery voltage, check:
- Ignition coil.
- WHT/BLU wire between the ignition coil and the ICM.
- If there is battery voltage, go to step 5.
5. Check the YEL/GRN wire between the ECM and the ICM.
6. Check the BLU wire between the tachometer and the ICM.
7. If all tests are normal, replace the ICM.
- Perform an input test for the Ignition Control Module (ICM) after finishing the fundamental tests for the ignition system and the fuel and emissions systems.
- The tachometer should operate normally.
Distributor Components:
1. Remove the distributor cap, the distributor rotor, and the leak cover.
Ignition Control Module:
2. Disconnect the BLK/YEL, WHT/BLU, YEL/GRN, and BLU wires from the ICM.
3. Turn the ignition switch ON. Check for voltage between the BLK/YEL wire and body ground. There should be battery voltage.
- If there is no battery voltage, check the BLK/YEL wire between the ignition switch and the ICM.
- If there is battery voltage, go to step 4.
4. Turn the ignition switch ON. Check for voltage between the WHT/BLU wire and body ground. There should be battery voltage.
- If there is no battery voltage, check:
- Ignition coil.
- WHT/BLU wire between the ignition coil and the ICM.
- If there is battery voltage, go to step 5.
5. Check the YEL/GRN wire between the ECM and the ICM.
6. Check the BLU wire between the tachometer and the ICM.
7. If all tests are normal, replace the ICM.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.