Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1992 Acura Integra GS-RFACTORY OEM SERVICE PROCEDURE
Wheel Alignment Specifications
WHEEL ALIGNMENT SPECIFICATIONS
| Application | Preferred | Range | ||||||
|---|---|---|---|---|---|---|---|---|
| Integra | ||||||||
| Camber (1) | ||||||||
| Front | 0 | - 1 To 1 | ||||||
| Rear | - 0.67 | - 1.67 To 0.33 | ||||||
| Caster (1) | ||||||||
| Front | 1.5 | 0.5 To 2.5 | ||||||
| Toe-In (1) | ||||||||
| Front | 0 | - 0.16 To 0.16 | ||||||
| Rear | 0.16 | 0 To 0.24 | ||||||
| Toe-In (2) | ||||||||
| Front | 0 (0) | - 0.08 To 0.08 (- 2 To 2) | ||||||
| Rear | 0.08 (2) | 0 To 0.12 (0 To 3) | ||||||
| Toe-Out On Turns (1) | ||||||||
| Inner | 40.5 | N/A | ||||||
| Outer | 32 | N/A | ||||||
| Legend | ||||||||
| Camber (1) | ||||||||
| Front | 0 | - 1 To 1 | ||||||
| Rear | - 0.33 | 1.33 To 0.67 | ||||||
| Caster (1) | ||||||||
| Front | 3.75 | 2.75 To 4.75 | ||||||
| Toe-In(1) | ||||||||
| Front | - 0.08 | - 0.24 To 0.08 | ||||||
| Rear | 0.16 | 0 To 0.32 | ||||||
| Toe-In (2) | ||||||||
| Front | - 0.04 (- 1) | - 0.12 To 0.04 (- 3 To 1) | ||||||
| Rear | 0.08 (2) | 0 To 0.16 (0 To 4) | ||||||
| Toe-Out On Turns (1) | ||||||||
| Inner | 44 | N/A | ||||||
| Outer | 35 | N/A | ||||||
| Vigor | ||||||||
| Camber (1) | ||||||||
| Front | 0 | - 1 To 1 | ||||||
| Rear | - 0.5 | - 1.5 To 0.5 | ||||||
| Caster (1) | ||||||||
| Front | 1.63 | 0.63 To 2.63 | ||||||
| Toe-In (1) | ||||||||
| Front | 0 | - 0.16 To 0.16 | ||||||
| Rear | 0.24 | 0.06 To 0.4 | ||||||
| Toe-In (2) | ||||||||
| Front | 0 (0) | - 0.08 To 0.08 (-2 To 2) | ||||||
| Rear | 0.12 | 0.04 To 0.2 (1 To 5) | ||||||
| Toe-Out On Turns (1) | ||||||||
| Inner | 39.4 | N/A | ||||||
| Outer | 33.6 | N/A | ||||||
|
||||||||
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.